1700-81-8025 (Hotline), +603-5192 7333 (Office) sales@safetysolutions.com.my
 

SELLEYS Liquid Nails High Strength 320g

Previous 1 / 9 Next

SELLEYS Liquid Nails High Strength 320g  Adhesives & Sealants


  • Description
Liquid Nails High Strength is a premium grade multipurpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails High Strength is flexible enough to response to movement allowing a steong bond to be maintained over time.

Certifications
  • Strong bond - will cope with shrinkage and thermal movement.
  • Adheres well to wet and dry timber (no need to for timber to dry).
  • Easily extruded and easy to use in low winter temperatures.
  • Paintable when dry (quality finished job).
  • Doesn't drip, sag or string (less mess).
  • Bridges gaps on rough and ill fitting construction material.
  • Life expectancy of about 20 years.
  • Not for use on polyethylene, polypropylene, teflon, silicone or polystrene.
Ideal for
  • Timber 
  • Concrete
  • Hardboards 
  • Particle board 
  • Masonry 
  • Ceramic Tiles
  • Plaster board 
  • Painted Surfers
  • Metal 
  • Plastics
  • Rubber 
  • Glass
  • Brick
  • MPF
  • Render
Direction
  • Ensure the surfaces to be bonded are clean, dry and free from dust, grease, oil and loose powdery materials. If porous surfaces are greasy or dirty, we would recommend cleaning the surface and allow to dry. If the surface is non-porous eg glass or metal, firstly clean the surface with Mineral Turpentine and then again with Methylated Spirits, and allow to dry. On wet timber pooled water should be wiped off.  Highly oily timber types may need to be wiped with solvent prior to application to remove surface oils.
  • We also recommend sanding the surface back with a good quality sanding block, as the construction adhesive will adhere more readily to a scratched up surface.
  • Apply a bead of product along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm.
  • Fix the surfaces with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. The product is repositionable for up to 20 minutes after fitting.
  • Allow the adhesive to set (at least 24 hours) before removing any temporary fasteners or clamping. For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-5 minutes before firmly joining.
  • The time it takes to form a strong bond depends on the nature and conditions of the application. In most situations strong bonds can be achieved after 24 hours and will continue to strengthen over a 2-3 day period. The product will fully cure up to 7 days.
  • When the product is still wet it can be removed with mineral turpentine, otherwise if the product is dry it can be removed by sanding or scraping.
  • To eliminate squeaks in tongue and groove flooring, apply a bead of Liquid Nails into the groove or each board when installing.
Safety tips
  • If swallowed, do NOT induce vomiting.
  • Avoid prolonged skin contact.
  • Ensure you use a well ventilated area.
  • Highly flammable. Vapours can be ignited by flames or sparks.
  • Avoid contamination of waterways. Allow waste or left over product to completely dry out before disposing of it.
  • Avoid breathing in vapours. Intentional misuse or deliberately inhaling the vapours from this product can be harmful or fatal.
  • For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
  • Keep away from children.

Please leave your enquiry here, we will reply as soon as possible.
Name*  
Company Name  
Product Interested  
Quantity  
Email*  
Contact No.*  
Attachment  
*only support gif, jpeg, jpg, png, pdf
Messages*  

Switch to Mobile Version
Subscribe Newsletter
1
Hello! Thanks for visiting my site. Please press Start button to Contact with Admin :)

Start